>>DISTRIBUTION STANDARDS<< |
|
SITE LINKS | ||||
New Roads & Street Works Act (NURSWA) | |
Gas Safety (Management) Regulations | |
IGE/TD/3 Edition 4 | Steel and PE pipelines for gas distribution |
IGE/TD/3 Edition 4 Supp1 | Handling,transport and storage of PE pipe and fittings |
IGE/TD/4 Edition 3 | Gas services |
IGE/TD/13 | Pressure regulating installations for transmission and distribution systems |
IGE/TD/15 | Services and metering installations for a gas flow not exceeding 6m3/hr at supply MOP exceeding 75mbar but not exceeding 2 bar |
IGE/TD/101 | Adoption of pipe systems by a GT - management of UIP activities |
1GE/SR/4 Ed2 | Low pressure gas storage |
IGE/SR/9 Ed 2 | Safe working practice for pressure regulating installations |
1GE/SR/10 Ed 2 | Procedures for dealing with escapes of gas into underground plant |
IGE/SR/20 Ed 2 | Dealing with reported gas escapes |
IGE/SR/22 | Purging operations for fuel gases in transmission, distribution and storage |
IGE/SR/23 | Venting of natural gas |
IGE/SR/25 | Hazardous area classification of Natural Gas installations |
IGE/SR/26 | Horizontal directional drilling and impact moling |
IGE/SR/28 | Trenchless techniques |
IGE/SR/28 | Operators guides(set of 11 encapsulation guides) |
IGE/GL/1 | Planning for gas distribution systems operating at pressures not exceeding 7 bar |
IGE/GL/3 | Network emergency procedures |
IGE/GL/5 | Plant modification procedures |
IGE/GL/6 | Non-routine operations |
BS 21:1985 | Specification for pipe threads for tubes and fittings where pressure-tight joints are made on the threads (metric dimensions) |
BS 78-2:1965 | Specification for cast iron spigot and socket pipes (vertically cast) and spigot and socket fittings. Fittings |
BS 1179:1967 | Glossary of terms used in the gas industry |
BS 1211:1958 | Specification for centrifugally cast (spun) iron pressure pipes for water, gas and sewage |
BS 1552:1995 | Specification for open bottomed taper plug valves for 1st, 2nd and 3rdfamily gases up to 200 mbar |
BS 2971:1991 | Specification for class II arc welding of carbon steel pipework for carrying fluids |
BS 2633:1987 | Specification for Class I arc welding of ferritic steel pipework for carrying fluids |
BS 2640:1982 | Specification for Class II oxy-acetylene welding of carbon steel pipework for carrying fluids |
BS 5834-1:1985 | Surface boxes, guards and underground chambers for gas and waterworks purposes. Specification for guards, including foundation units |
BS 5834-2:1983 | Surface boxes, guards and underground chambers for gas and waterworks purposes. Specification for small surface boxes |
BS 5834-3:1985 | Surface boxes, guards and underground chambers for gas and waterworks purposes. Specification for large surface boxes |
BS 5834-4:1989 | Surface boxes, guards and underground chambers for gas and waterworks purposes. Specification for preformed chambers |
BS 5958-2:1991 | Code of practice for control of undesirable static electricity. Recommendations for particular industrial situations |
BS 6713-2:1986, EN
26184-2:1991, ISO 6184-2:1985 |
Explosion protection systems. Method for determination of explosion indices of combustible gases in air |
BS 7336:1990 | Specification for polyethylene fusion fittings with integral heating element(s) for use with polyethylene pipes for the conveyance of gaseous fuels |
BS 7461:1991 | Specification for electrically operated automatic gas shut-off valves fitted with throughput adjusters, proof of closure switches, closed position indicator switches or gas flow control |
BS 8010-2.1:1987 | Code of practice for pipelines. Pipelines on land: design, construction and installation. Ductile iron |
BS 8010-2.8:1992 | Code of practice for pipelines. Pipelines on land: design, construction and installation. Steel for oil and gas |
CP 2010-2:1970 | Code of practice for pipelines. Design and construction of steel pipelines in land |
PD CR 13737:2000 | Implementation guide for functional standards prepared by CEN/TC 234 'Gas supply' |
BS EN ISO 6326-5:1998,
BS 3156-11.4.5:1994 |
Natural gas. Determination of sulfur compounds. Lingener combustion method |
BS ISO 8085-1:2001 | Polyethylene fittings for use with polyethylene pipes for the supply of gaseous fuels. Metric series. Specifications. Fittings for socket fusion using heated tools |
BS ISO 8085-2:2001 | Polyethylene fittings for use with polyethylene pipes for the supply of gaseous fuels. Metric series. Specifications. Spigot fittings for butt fusion, for socket fusion using heated tools and for use with eletrofusion fittings |
BS ISO 8085-3:2001 | Polyethylene fittings for use with polyethylene pipes for the supply of gaseous fuels. Metric series. Specifications. Electrofusion fittings |
BS EN ISO 10715:2001, BS 3156-11.0.1:2001 |
Natural gas. Sampling guidelines |
BS ISO 10838-1:2000 | Mechanical fittings for polyethylene piping systems for the supply of gaseous fuels. Metal fittings for pipes of nominal outside diameter less than or equal to 63mm |
BS ISO 10838-2:2000 | Mechanical fittings for polyethylene piping systems for the supply of gaseous fuels. Metal fittings for pipes of nominal outside diameter greater than 63mm |
BS ISO 14531-1:2002 | Plastics pipes and fittings. Crosslinked polyethylene (PE-X) pipe systems for the conveyance of gaseous fuels. Metric series. Specifications. Pipes |
BS ISO 13953:2001 | Polyethelene (PE) pipes and fittings. Determination of the tensile strength and failure mode of test pieces from a butt-fused joint |
BS EN 10284:2000 | Malleable cast iron fittings with compression ends for polyethylene (PE) piping systems |
BS EN 1716:1997, BS
2782-11: Method 1108T:1997 |
Plastics piping systems. Polyethylene (PE) tapping tees. Test method for impact resistance of an assembled tapping tee |
BS ISO 10838-3:2001 | Mechanical fittings for polyethylene piping systems for the supply of gaseous fuels. Thermoplastic fittings for pipes of nominal outside diameter less than or equal to 63mm |
BS ISO 14532:2001 | Natural gas. Vocabulary |
BS EN ISO 15761:2002 | Steel gate, globe and check valves for sizes DN 100 and smaller, for the petroleum and natural gas industries |
BS ISO/TS 16922:2002 | Natural gas. Guidelines for odorizing gases |
BS EN 288-9:1999 | Specification and approval of welding procedures for metallic materials. Welding procedure test for pipeline welding on land and offshore site butt welding of transmission pipelines |
BS EN 331:1998 | Manually operated ball valves and closed bottom taper plug valves for gas installations in buildings |
BS EN 334:1999 | Gas pressure regulators for inlet pressures up to 100 bar |
BS EN 751-1:1997 | Sealing materials for metallic threaded joints in contact with 1st, 2nd and 3rd family gases and hot water. Anaerobic jointing compounds |
BS EN 751-2:1997 | Sealing materials for metallic threaded joints in contact with 1st, 2nd and 3rd family gases and hot water. Non-hardening jointing compounds |
BS EN 751-3:1997 | Sealing materials for metallic threaded joints in contact with 1st, 2nd and 3rd family gases and hot water. Unsintered PTFE tapes |
BS EN 969:1996 | Specification for ductile iron pipes, fittings, accessories and their joints for gas pipelines. Requirements and test methods |
BS EN 1593:1999 | Non-destructive testing. Leak testing. Bubble emission techniques |
BS EN 1680:1997,
BS 2782-11: Method 1133A:1997 |
Plastics piping systems. Valves for polyethylene (PE) piping systems.Test method for leaktightness under and after bending applied to the operating mechanism |
BS EN 1708-1:1999 | Welding. Basic weld joint details in steel. Pressurized components |
BS EN 10284:2000 | Malleable cast iron fittings with compression ends for polyethylene (PE) piping systems |
BS EN 12007-1:2000 | Gas supply systems. Pipelines for maximum operating pressure up to and including 16 bar. General functional recommendations |
BS EN 12007-2:2000 | Gas supply systems. Pipelines for maximum operating pressure up to and including 16 bar. Specific functional recommendations for polyethylene (MOP up to and including 10 bar) |
BS EN 12007-3:2000 | Gas supply systems. Pipelines for maximum operating pressure up to and including 16 bar. Specific functional recommendations for steel |
BS EN 12007-4:2000 | Gas supply systems. Pipelines for maximum operating pressure up to and including 16 bar. Specific functional recommendations for renovation |
BS EN 12083:1998 | Respiratory protective devices. Filters with breathing hoses, (non-mask mounted filters). Particle filters, gas filters, and combined filters. Requirements, testing, marking |
BS EN 12186:2000 | Gas supply systems. Gas pressure regulating stations for transmission and distribution. Functional requirements |
BS EN 12279:2000 | Gas supply systems. Gas pressure regulating installations on service lines. Functional requirements |
BS EN 12327:2000 | Gas supply systems. Pressure testing, commissioning and decommissioning procedures. Functional requirements |
BS EN 12419:1999 | Respiratory protective devices. Light duty construction compressed airline breathing apparatus incorporating a full face mask, half mask or quarter mask. Requirements, testing, marking |
BS EN 12874:2001 | Flame arresters. Performance requirements, test methods and limits for use |
BS EN 13185:2001 | Non-destructive testing. Leak testing. Tracer gas method |
BS EN 13774:2003 | Valves for gas distribution systems with maximum operating pressure less than or equal to 16 bar. Performance requirements |
BS EN 13787:2001 | Elastomers for gas pressure regulators and associated safety devices for inlet pressures up to 100 bar |
BS EN 14382:2002 | Safety devices for gas pressure regulating stations and installations.Gas safety shut-off devices for operating pressure up to 100 bar |
BS EN 60079-7:2003 | Electrical apparatus for explosive gas atmospheres. Increased safety "e" |
BS EN 60079-10:2003 | Electrical apparatus for explosive gas atmospheres. Classification of hazardous areas |
BS EN 60079-14:2003 | Electrical apparatus for explosive gas atmospheres. Electrical installations in hazardous areas (other than mines) |
BS EN 60079-15:2003 | Electrical apparatus for explosive gas atmospheres. Type of protection "n" |
BS EN 60079-17:2003 | Electrical apparatus for explosive gas atmospheres. Inspection and maintenance of electrical installations in hazardous areas (other than mines) |
TH 42091 | CE Marking for Pressure Equipment. A guide to the European Directive |
96/540970 DC | Maintenance for portable fire extinguishers. (EN 12367 |
98/260075 DC | Specification for general requirements for the construction, testing and performance of electrically operated combustible gas detection apparatus, designed for continuous operation in a fixed installation in recreational craft (CENELEC document CLC/TC 216) |
00/123576 DC | BS ISO 18453. Natural gas. Correlation between water content and water dew point (ISO/CD 18453) |
00/708220 DC | Specification and approval of welding procedures for approval by a standard welding procedure |
01/123802 DC | BS ISO 14531-2. Plastics pipes and fittings. Cross linked polyethylene (PE-X) pipe systems for the transport of gaseous fuels. Metric series. Specifications. Part 2. Fittings for heat fusion jointing |
01/708672 DC | prEN 14141. Valves for natural gas transportation in pipelines. Performance requirements and tests |
02/121565 DC | BS EN 14408-1. Plastics piping systems for the renovation of underground gas supply networks. Part 1: General |
02/121566 DC | BS EN 14408-3. Plastics piping systems for the renovation of underground gas supply networks. Part 3: Lining with close-fit pipes |
02/705734 DC | ISO/DIS 17292. Metal ball valves for petroleum, petrochemical and allied industries |
02/711048 DC | EN ISO 10434. Bolted bonnet steel gate valves for the petroleum and natural gas industries |
03/316975 DC | ISO 15590-3. Petroleum and natural gas industries. Induction bends, fitting and flanges for pipeline transportation systems. Part 3. Flanges |
BS 1560:Part 2:1970 | Circular flanges for pipes, valves and fittings (Class designated). Specification for steel pipe flanges (nominal sizes 1/2 in to 24 in). Metric dimensions |
BS 3554:Part 1:1971 | Specification for gas governors. Independent governors for inlet pressures up to 25 mbar |
BS 3554:Part 2:1972 | Specification for gas governors. Independent governors for inlet pressures up to 350 mbar |
BS 4515:1969 | Specification for field welding of carbon steel pipelines |
BS 6959:1988 | Code of practice for selection, installation, use and maintenance of apparatus for the detection and measurement of combustible gases (other than for mining applications or explosives processing and manufacture) |
BS 10:1962 | Specification for flanges and bolting for pipes, valves, and fittings |
BS 1387:1985 | Specification for screwed and socketed steel tubes and tubulars and for plain end steel tubes suitable for welding or for screwing to BS 21 pipe threads |
BS 1560-3.1:1989 | Circular flanges for pipes, valves and fittings (Class designated). Steel, cast iron and copper alloy flanges. Specification for steel flanges |
BS 1965-1:1963 | Specification for butt-welding pipe fittings for pressure purposes. Carbon steel |
BS 2035:1966 | Specification for cast iron flanged pipes and flanged fittings |
BS 2782-11:Method 1150B:1998, ISO 11414:1996 |
Methods of testing plastics. Thermoplastics pipes, fittings and valves. Plastics pipes and fittings. Preparation of polyethylene (PE) pipe/pipe or pipe/fitting test piece assemblies by butt fusion |
BS 2782-11:Method 1150E:1997, ISO | Methods of testing plastics. Thermoplastics pipes, fittings and valves .Plastics pipes and fittings. Preparation of test piece assemblies between |
11413:1996 | a polyethylene (PE) pipe and an electrofusion fitting |
BS 3063:1965 | Specification for dimensions of gaskets for pipe flanges |
BS 4882:1990 | Specification for bolting for flanges and pressure containing purposes |
BS 5114:1975 | Specification for performance requirements for joints and compression fittings for use with polyethylene pipes |
BS 7336:1990 | Specification for polyethylene fusion fittings with integral heating element(s)for use with polyethylene pipes for the conveyance of gaseous fuels |
BS EN 1514-1:1997 | Flanges and their joints. Dimensions of gaskets for PN-designated flanges.Non-metallic flat gaskets with or without inserts |
BS EN 1515-1:2000 | Flanges and their joints. Bolting. Selection of bolting |
BS EN 1515-2:2001 | Flanges and their joints. Bolting. Classification of bolt materials for steel flanges, PN designated |
BS EN 10241:2000 | Steel threaded pipe fittings |
BS EN 10242:1995 | Threaded pipe fittings in malleable cast iron |
ANSI B16.5 | Pipe flanges and flanged fittings |
ANSI B16.11 | Forge fittings, socket-welding and threaded |
HOME | GAS TRANSMISSION | GAS DISTRIBUTION | GAS IN INDUSTRY | GAS IN THE HOME | CONTACT US |